How To Make a Rope Fence (Q and A)

DIY Articles

Chuck Stewart

Article Description

Question: What size diameter of rope do I need?

Answer: Typically, you want to use the largest size within your budget for the project. If you have a 4x4 post that is typically 1-¼" - 1-½" Diameter; For a 6x6 post that is 1-½" - 2” Diameter.

Question: How much rope do I need for my project?

Answer: This depends on what kind of sag you are looking for in your project.  To figure this out you can take a tape measure and run it from one post to the next then add slack until you reach the desired look you want to achieve. For most people they usually like about 3” in slack in the rope from one post to the next. Take the overall length and then add in the additional inches for the sag.

Question: How do I calculate the amount of rope I will need to wrap a round post?

Answer: Multiple the diameter (width) of the post times 3.14 (π). Use the centerline of the rope by adding the diameter of the rope to the diameter of the post.

Example:

Post diameter:                              9.5”

Plus rope diameter:                   +2”

Centerline of rope=                    11.5”

Diameter (11.5) x 3.14 = Length (36”)

*Approximately 36” to get around the post 1 time

 

Question: How do I cut my rope if I do not need the entire length?

Answer: If you need to cut the rope, you can use a rope hot cutter available at hardware stores or normal household tools, if you do not want to invest in tools that you won’t likely use again. Using a household tools such as electric tape, a serrated knife and a hot non-stick skillet will also work. First you want to wrap the end tightly at the point you want to cut and then use a serrated knife to cut the end to the desired length. Next you want to seal it, place the cut wrapped end on a hot skillet to melt the end and seal it.

 

Question: How do I attach or tie-off the rope at the end post?

Answer: There are several different options, we have three options below.

  • Option 1: If you do not want your rope to show and end inside the post. You will want to mark both sides of the post and then drill approximately halfway through the post a diameter slightly larger than your rope. To do this you can use a drill press (recommended) or a heavy-duty hand drill. You will want to use either a Threaded Forstner bit or a Hole Saw the appropriate diameter for your rope. Please note with the Hole Saw you will have to chisel out the wood. In addition, If your rope diameter is less than 1-½" you can use a spade bit. Once you have created a hole in your post for your rope to nest, you can screw through the opposite side directly into the center of your rope which is wrapped tight at the end. If you want the screw not to be noticeable and for it to look nice, Pre-drill and countersink the screw.
  • Option 2: Tying a knot at the end. You will need 12 times the diameter extra length to tie the knot.
  • Option 3: Wrap the post. Wrap the post in the fashion you want it to look and then use lag screws or stainless-steel deck screws in the center of the rope to attach it in place. Use long enough screws to go through the rope and halfway through the post. Generally, 2-3 screws per post is enough.
Chuck Stewart
Meet the Author

Chuck Stewart

Rope Holders

Learn more

Post Caps

Learn more

Round Post Caps

Learn more

Plain Post Caps

Learn more

Round Post Toppers

Learn more

Rope Holders

Learn more

Post Caps

Learn more

Round Post Caps

Learn more

Plain Post Caps

Learn more

Round Post Toppers

Learn more

Rope Holders

Learn more

Post Caps

Learn more

Round Post Caps

Learn more

Plain Post Caps

Learn more

Round Post Toppers

Learn more

Rope Holders

Learn more

Post Caps

Learn more

Round Post Caps

Learn more

Plain Post Caps

Learn more

Round Post Toppers

Learn more

Leave a comment

Please note: comments must be approved before they are published.